DONAT STEMSciences and MathsENFR
Physics · Simulation and virtual lab Free

Alternating current: read peak, r.m.s. and frequency

Set the Y-gain and the time-base, read the wave on the oscilloscope screen and find V₀, T, f and the r.m.s. voltage.

  • Best for S6 · Unit 4: Alternating current
  • Also useful S6 · Unit 9: Introduction to electronics (diodes, rectification and smoothing)
  • Also useful S6 · Unit 3: Electromagnetic induction (the alternating emf of a generator)
You will learn to
  • Read the peak voltage and the period from an oscilloscope using the Y-gain and the time-base.
  • Calculate frequency and r.m.s. values, and show that V(r.m.s.) = V₀ ÷ √2.
  • Describe half-wave rectification, smoothing and the phase of current in a capacitor.
You will measure
Peak height and cycle length in divisions; then V₀ (V), T (ms), f (Hz) and V(r.m.s.).
Time needed
About 35–45 min
Equipment
Nothing extra. Real version: low-voltage AC supply (signal generator), oscilloscope, resistor, diode, capacitor, AC voltmeter.
Price
Free: no payment, no account.

Simulation

The electricity that reaches homes from REG is alternating current at 50 Hz and 230 V. A technician who repairs phone chargers and solar inverters uses an oscilloscope to see the wave. Here you learn to read the screen as they do.

Change and observe

Virtual lab

Follow the steps with the simulation above (go back to the simulation ↑). Each time you tap Record, a row is added to the table and a point to the graph.

Aim

To measure the peak voltage, period and frequency of an alternating voltage with an oscilloscope, to show that V(r.m.s.) = V₀ ÷ √2, and to observe rectification and smoothing.

What to do

  1. Keep the Resistor, V₀ = 6 V and 50 Hz. Choose a Y-gain so the wave fits the screen. Count the divisions from the centre line to the top of the wave.
  2. Choose a time-base so that one or two full waves are on the screen. Count the divisions for one full cycle.
  3. Tap Record my reading. Calculate V₀ = divisions × V/div and T = divisions × ms/div, then f = 1/T. Check with Show the values.
  4. Record for V₀ = 2, 4, 8, 10 and 12 V. The graph of voltmeter reading against V₀ gives the r.m.s. factor.
  5. Change the frequency to 25, 100 and 200 Hz and measure T each time.
  6. Choose the Capacitor, then the Diode, then Diode + capacitor. Describe each trace.

Results

📏 Read the instruments carefully

InstrumentSmallest readingUncertainty
Oscilloscope screen0.2 division (minor tick)± 0.1 division
AC voltmeter0.01 V± 0.01 V

Write every reading with its unit, and with the same number of decimal places as the instrument. Use the 🔍 Magnifier on the picture to read small scales at eye level.

⚠️ Avoid these mistakes

  • Measuring the peak from the bottom of the wave to the top: that is 2V₀ (peak-to-peak).
  • Forgetting to change milliseconds into seconds before f = 1/T.
  • Thinking the mains peak is 230 V: 230 V is the r.m.s. value; the peak is 325 V.

✍️ Conclusion

Write your own conclusion first: what do your results and graph show, and which law or principle do they support?

Check your conclusion

The peak voltage is the number of divisions from the centre line × the Y-gain, and the period is the divisions for one cycle × the time-base; f = 1/T. The voltmeter reading is proportional to V₀ with gradient 1/√2, so V(r.m.s.) = 0.707 V₀. A diode removes one half of each cycle and a capacitor smooths the output.

Questions

What does the Y-gain of an oscilloscope tell you?

The voltage represented by one vertical division (for example 2 V/div). Peak voltage = number of divisions from the centre line to the peak × Y-gain.

A wave has a period of 4 divisions with the time-base on 5 ms/div. Find its frequency.

T = 4 × 5 ms = 20 ms = 0.020 s, so f = 1 ÷ 0.020 = 50 Hz.

What is the r.m.s. value of an alternating voltage?

The value of the steady (direct) voltage that would produce the same heating effect in a resistor. For a sine wave V(r.m.s.) = V₀ ÷ √2.

The mains supply is 230 V r.m.s. What is its peak voltage?

V₀ = 230 × √2 = 325 V.

What does the diode do to the wave?

It conducts in one direction only, so the negative half-cycles are removed (half-wave rectification). Each peak is about 0.7 V lower because of the voltage across the diode.

Why does a capacitor make the output smoother?

It charges to the peak voltage and then discharges slowly through the load between peaks, so the voltage falls only a little (ripple) before the next peak.

For teachers: expected results and how the model works

The screen has 10 × 8 divisions with 5 minor ticks per division on the centre lines. With V₀ = 6 V and 2 V/div the peak is 3.0 div; at 50 Hz and 5 ms/div one cycle is 4.0 div. The AC voltmeter reads V₀ ÷ √2 (sine wave only, so it shows “—” for the rectified traces). The diode model removes 0.7 V; smoothing uses RC = 8 periods, giving about 12 % ripple. The capacitor mode shows the current leading the voltage by 90°.

Quick check 3 questions · scored

Choose one answer for each question. You see at once if it is right, why, and your score at the end.

1. Y-gain 2 V/div; the peak is 3 divisions above the centre. What is V₀?

2. One cycle covers 4 divisions at 5 ms/div. What is the frequency?

3. V₀ = 10 V. What does an AC voltmeter read?

Exam practice Exam set

National-exam style questions on this simulation (17 marks). Try each one on paper first, then open the marking scheme.

An alternating voltage is displayed on an oscilloscope set at 5 V/div and 2 ms/div. The peak is 2.4 divisions above the centre line and one cycle covers 5 divisions. Calculate (a) the peak voltage, (b) the r.m.s. voltage, (c) the frequency. (6 marks)

Marking scheme: (a) V₀ = 2.4 × 5 = 12 V (1, 1). (b) V(r.m.s.) = 12 ÷ √2 = 8.5 V (1, 1). (c) T = 5 × 2 = 10 ms (1), f = 1 ÷ 0.010 = 100 Hz (1).

Define the r.m.s. value of an alternating current. (2 marks)

Marking scheme: The value of the direct current (1) that would dissipate the same power / produce the same heating in the same resistor (1).

A 230 V r.m.s., 50 Hz supply is connected to a 1 150 W kettle. Calculate the r.m.s. current and the peak current. (3 marks)

Marking scheme: I(r.m.s.) = P ÷ V = 1 150 ÷ 230 = 5.0 A (1, 1). I₀ = 5.0 × √2 = 7.1 A (1).

Draw the output of a half-wave rectifier, with and without a smoothing capacitor, and explain the difference. (4 marks)

Marking scheme: Half-cycles only, gaps between them (1). With capacitor: nearly steady line with small ripple (1). Capacitor charges at each peak (1) and discharges slowly through the load between peaks (1).

For a capacitor in an AC circuit, state the phase difference between current and voltage. (2 marks)

Marking scheme: The current leads the voltage (1) by 90° (π/2 rad, a quarter of a cycle) (1).

For class and homework

Teacher resources

The worksheet has the steps, an empty results table, a graph grid and all the questions with answer lines. The marking scheme has the expected results and every answer with its marks.

Keep learning

More free practice: Circuit Construction Kit: AC (external website, by PhET Interactive Simulations, University of Colorado Boulder). It opens in a new tab.

This simulation is an original model made for Rwandan learners. Real experiments can give slightly different numbers: a simulation never replaces handling real apparatus when your school has it.