Physics · Simulation and virtual lab Free
Alternating current: read peak, r.m.s. and frequency
Set the Y-gain and the time-base, read the wave on the oscilloscope screen and find V₀, T, f and the r.m.s. voltage.
- You will learn to
- Read the peak voltage and the period from an oscilloscope using the Y-gain and the time-base.
- Calculate frequency and r.m.s. values, and show that V(r.m.s.) = V₀ ÷ √2.
- Describe half-wave rectification, smoothing and the phase of current in a capacitor.
- You will measure
- Peak height and cycle length in divisions; then V₀ (V), T (ms), f (Hz) and V(r.m.s.).
- Time needed
- About 35–45 min
- Equipment
- Nothing extra. Real version: low-voltage AC supply (signal generator), oscilloscope, resistor, diode, capacitor, AC voltmeter.
- Price
- Free: no payment, no account.
Virtual lab
Follow the steps with the simulation above (go back to the simulation ↑). Each time you tap Record, a row is added to the table and a point to the graph.
Aim
To measure the peak voltage, period and frequency of an alternating voltage with an oscilloscope, to show that V(r.m.s.) = V₀ ÷ √2, and to observe rectification and smoothing.
What to do
- Keep the Resistor, V₀ = 6 V and 50 Hz. Choose a Y-gain so the wave fits the screen. Count the divisions from the centre line to the top of the wave.
- Choose a time-base so that one or two full waves are on the screen. Count the divisions for one full cycle.
- Tap Record my reading. Calculate V₀ = divisions × V/div and T = divisions × ms/div, then f = 1/T. Check with Show the values.
- Record for V₀ = 2, 4, 8, 10 and 12 V. The graph of voltmeter reading against V₀ gives the r.m.s. factor.
- Change the frequency to 25, 100 and 200 Hz and measure T each time.
- Choose the Capacitor, then the Diode, then Diode + capacitor. Describe each trace.
Results
📏 Read the instruments carefully
| Instrument | Smallest reading | Uncertainty |
|---|
| Oscilloscope screen | 0.2 division (minor tick) | ± 0.1 division |
| AC voltmeter | 0.01 V | ± 0.01 V |
Write every reading with its unit, and with the same number of decimal places as the instrument. Use the 🔍 Magnifier on the picture to read small scales at eye level.
⚠️ Avoid these mistakes
- Measuring the peak from the bottom of the wave to the top: that is 2V₀ (peak-to-peak).
- Forgetting to change milliseconds into seconds before f = 1/T.
- Thinking the mains peak is 230 V: 230 V is the r.m.s. value; the peak is 325 V.
✍️ Conclusion
Write your own conclusion first: what do your results and graph show, and which law or principle do they support?
Check your conclusion
The peak voltage is the number of divisions from the centre line × the Y-gain, and the period is the divisions for one cycle × the time-base; f = 1/T. The voltmeter reading is proportional to V₀ with gradient 1/√2, so V(r.m.s.) = 0.707 V₀. A diode removes one half of each cycle and a capacitor smooths the output.
Questions
What does the Y-gain of an oscilloscope tell you?
The voltage represented by one vertical division (for example 2 V/div). Peak voltage = number of divisions from the centre line to the peak × Y-gain.
A wave has a period of 4 divisions with the time-base on 5 ms/div. Find its frequency.
T = 4 × 5 ms = 20 ms = 0.020 s, so f = 1 ÷ 0.020 = 50 Hz.
What is the r.m.s. value of an alternating voltage?
The value of the steady (direct) voltage that would produce the same heating effect in a resistor. For a sine wave V(r.m.s.) = V₀ ÷ √2.
The mains supply is 230 V r.m.s. What is its peak voltage?
V₀ = 230 × √2 = 325 V.
What does the diode do to the wave?
It conducts in one direction only, so the negative half-cycles are removed (half-wave rectification). Each peak is about 0.7 V lower because of the voltage across the diode.
Why does a capacitor make the output smoother?
It charges to the peak voltage and then discharges slowly through the load between peaks, so the voltage falls only a little (ripple) before the next peak.
For teachers: expected results and how the model works
The screen has 10 × 8 divisions with 5 minor ticks per division on the centre lines. With V₀ = 6 V and 2 V/div the peak is 3.0 div; at 50 Hz and 5 ms/div one cycle is 4.0 div. The AC voltmeter reads V₀ ÷ √2 (sine wave only, so it shows “—” for the rectified traces). The diode model removes 0.7 V; smoothing uses RC = 8 periods, giving about 12 % ripple. The capacitor mode shows the current leading the voltage by 90°.
Quick check 3 questions · scored
Choose one answer for each question. You see at once if it is right, why, and your score at the end.
1. Y-gain 2 V/div; the peak is 3 divisions above the centre. What is V₀?
V₀ = 3 × 2 = 6 V.
2. One cycle covers 4 divisions at 5 ms/div. What is the frequency?
T = 20 ms = 0.020 s; f = 1/T = 50 Hz.
3. V₀ = 10 V. What does an AC voltmeter read?
V(r.m.s.) = 10 ÷ √2 ≈ 7.1 V.
Your score:
Exam practice Exam set
National-exam style questions on this simulation (17 marks). Try each one on paper first, then open the marking scheme.
An alternating voltage is displayed on an oscilloscope set at 5 V/div and 2 ms/div. The peak is 2.4 divisions above the centre line and one cycle covers 5 divisions. Calculate (a) the peak voltage, (b) the r.m.s. voltage, (c) the frequency. (6 marks)
Marking scheme: (a) V₀ = 2.4 × 5 = 12 V (1, 1). (b) V(r.m.s.) = 12 ÷ √2 = 8.5 V (1, 1). (c) T = 5 × 2 = 10 ms (1), f = 1 ÷ 0.010 = 100 Hz (1).
Define the r.m.s. value of an alternating current. (2 marks)
Marking scheme: The value of the direct current (1) that would dissipate the same power / produce the same heating in the same resistor (1).
A 230 V r.m.s., 50 Hz supply is connected to a 1 150 W kettle. Calculate the r.m.s. current and the peak current. (3 marks)
Marking scheme: I(r.m.s.) = P ÷ V = 1 150 ÷ 230 = 5.0 A (1, 1). I₀ = 5.0 × √2 = 7.1 A (1).
Draw the output of a half-wave rectifier, with and without a smoothing capacitor, and explain the difference. (4 marks)
Marking scheme: Half-cycles only, gaps between them (1). With capacitor: nearly steady line with small ripple (1). Capacitor charges at each peak (1) and discharges slowly through the load between peaks (1).
For a capacitor in an AC circuit, state the phase difference between current and voltage. (2 marks)
Marking scheme: The current leads the voltage (1) by 90° (π/2 rad, a quarter of a cycle) (1).

Donat Sciences and MathsPhysics · Virtual lab worksheet
School: ........................................ Name: ................................ Class: ........ Date: ............
Alternating current: read peak, r.m.s. and frequency
Aim: To measure the peak voltage, period and frequency of an alternating voltage with an oscilloscope, to show that V(r.m.s.) = V₀ ÷ √2, and to observe rectification and smoothing.
Apparatus (real laboratory): low-voltage AC supply (signal generator), oscilloscope, resistor, diode, capacitor, AC voltmeter.
What to do (with the simulation on www.donatstem.co.rw)
- Keep the Resistor, V₀ = 6 V and 50 Hz. Choose a Y-gain so the wave fits the screen. Count the divisions from the centre line to the top of the wave.
- Choose a time-base so that one or two full waves are on the screen. Count the divisions for one full cycle.
- Tap Record my reading. Calculate V₀ = divisions × V/div and T = divisions × ms/div, then f = 1/T. Check with Show the values.
- Record for V₀ = 2, 4, 8, 10 and 12 V. The graph of voltmeter reading against V₀ gives the r.m.s. factor.
- Change the frequency to 25, 100 and 200 Hz and measure T each time.
- Choose the Capacitor, then the Diode, then Diode + capacitor. Describe each trace.
Results
| # | Circuit | Y-gain (V/div) | Peak height (div) | V₀ (V) | Time-base (ms/div) | One cycle (div) | T (ms) | f (Hz) | Voltmeter (V) |
|---|
| 1 | | | | | | | | | |
| 2 | | | | | | | | | |
| 3 | | | | | | | | | |
| 4 | | | | | | | | | |
| 5 | | | | | | | | | |
| 6 | | | | | | | | | |
| 7 | | | | | | | | | |
| 8 | | | | | | | | | |
| 9 | | | | | | | | | |
| 10 | | | | | | | | | |
Graph
Plot the voltmeter reading (V) on the vertical axis against V₀ (V). Draw the best straight line through the origin; its gradient should be 1/√2 ≈ 0.707.
Questions
- What does the Y-gain of an oscilloscope tell you? [2]
- A wave has a period of 4 divisions with the time-base on 5 ms/div. Find its frequency. [2]
- What is the r.m.s. value of an alternating voltage? [2]
- The mains supply is 230 V r.m.s. What is its peak voltage? [2]
- What does the diode do to the wave? [2]
- Why does a capacitor make the output smoother? [2]
- An alternating voltage is displayed on an oscilloscope set at 5 V/div and 2 ms/div. The peak is 2.4 divisions above the centre line and one cycle covers 5 divisions. Calculate (a) the peak voltage, (b) the r.m.s. voltage, (c) the frequency. [6]
- Define the r.m.s. value of an alternating current. [2]
- A 230 V r.m.s., 50 Hz supply is connected to a 1 150 W kettle. Calculate the r.m.s. current and the peak current. [3]
- Draw the output of a half-wave rectifier, with and without a smoothing capacitor, and explain the difference. [4]
- For a capacitor in an AC circuit, state the phase difference between current and voltage. [2]

Donat Sciences and MathsPhysics · Virtual lab worksheet
School: ........................................ Name: ................................ Class: ........ Date: ............
Marking scheme: Alternating current: read peak, r.m.s. and frequency
Expected results
The screen has 10 × 8 divisions with 5 minor ticks per division on the centre lines. With V₀ = 6 V and 2 V/div the peak is 3.0 div; at 50 Hz and 5 ms/div one cycle is 4.0 div. The AC voltmeter reads V₀ ÷ √2 (sine wave only, so it shows “—” for the rectified traces). The diode model removes 0.7 V; smoothing uses RC = 8 periods, giving about 12 % ripple. The capacitor mode shows the current leading the voltage by 90°.
Answers
- What does the Y-gain of an oscilloscope tell you? [2]
The voltage represented by one vertical division (for example 2 V/div). Peak voltage = number of divisions from the centre line to the peak × Y-gain.
- A wave has a period of 4 divisions with the time-base on 5 ms/div. Find its frequency. [2]
T = 4 × 5 ms = 20 ms = 0.020 s, so f = 1 ÷ 0.020 = 50 Hz.
- What is the r.m.s. value of an alternating voltage? [2]
The value of the steady (direct) voltage that would produce the same heating effect in a resistor. For a sine wave V(r.m.s.) = V₀ ÷ √2.
- The mains supply is 230 V r.m.s. What is its peak voltage? [2]
V₀ = 230 × √2 = 325 V.
- What does the diode do to the wave? [2]
It conducts in one direction only, so the negative half-cycles are removed (half-wave rectification). Each peak is about 0.7 V lower because of the voltage across the diode.
- Why does a capacitor make the output smoother? [2]
It charges to the peak voltage and then discharges slowly through the load between peaks, so the voltage falls only a little (ripple) before the next peak.
- An alternating voltage is displayed on an oscilloscope set at 5 V/div and 2 ms/div. The peak is 2.4 divisions above the centre line and one cycle covers 5 divisions. Calculate (a) the peak voltage, (b) the r.m.s. voltage, (c) the frequency. [6]
(a) V₀ = 2.4 × 5 = 12 V (1, 1). (b) V(r.m.s.) = 12 ÷ √2 = 8.5 V (1, 1). (c) T = 5 × 2 = 10 ms (1), f = 1 ÷ 0.010 = 100 Hz (1).
- Define the r.m.s. value of an alternating current. [2]
The value of the direct current (1) that would dissipate the same power / produce the same heating in the same resistor (1).
- A 230 V r.m.s., 50 Hz supply is connected to a 1 150 W kettle. Calculate the r.m.s. current and the peak current. [3]
I(r.m.s.) = P ÷ V = 1 150 ÷ 230 = 5.0 A (1, 1). I₀ = 5.0 × √2 = 7.1 A (1).
- Draw the output of a half-wave rectifier, with and without a smoothing capacitor, and explain the difference. [4]
Half-cycles only, gaps between them (1). With capacitor: nearly steady line with small ripple (1). Capacitor charges at each peak (1) and discharges slowly through the load between peaks (1).
- For a capacitor in an AC circuit, state the phase difference between current and voltage. [2]
The current leads the voltage (1) by 90° (π/2 rad, a quarter of a cycle) (1).